:AIL AIL :ELE ELE :THR THR :RUD RUD :RUD DR RUD DR :ELE DR ELE DR :AIL DR AIL DR :GEAR GEAR :MIX0 MIX0 :MIX1 MIX1 :MIX2 MIX2 :FMODE0 FMODE0 :FMODE1 FMODE1 :FMODE2 FMODE2 :TRIMLV- TRIMGV- :TRIMLV+ TRIMGV+ :TRIMRV- TRIMDV- :TRIMRV+ TRIMDV+ :TRIMLH- TRIMGH+ :TRIMLH+ TRIMGH+ :TRIMRH- TRIMDH+ :TRIMRH+ TRIMDH+ :TRIM_L- TRIM_G+ :TRIM_L+ TRIM_G+ :TRIM_R- TRIM_D- :TRIM_R+ TRIM_D+ :Left Gauche :Right Droite :Down Bas :Up Haut :Enter Entrée :Exit Sortie :RIGHT_H DROITE_H :LEFT_V GAUCHE_V :RIGHT_V DROITE_V :LEFT_H GAUCHE_H :None Néant :CYC CYC :Ch Ch :OK OK :Cancel Annuler :Unknown Inconnu :Load Charger :Center all sticks and touch the screen Mettre les manches au neutre et toucher l'écran :\nMove each stick to full max\nand min values then back to center.\nTouch the screen when finished \nBouger chaque manche en position\nmin et max puis revenir au centre. \nToucher ensuite l'écran :Calibrate Calibration :Test Test :Touch target %d Toucher la cible %d :Mode %d Mode %d :Off Off :Touch Calibrate Calibration du tactile :Touch Test Test du tactile :Change Changer :Configure Configurer :Language: Langage: :Stick Mode: Mode de pilotage: :Backlight: Rétroéclairage: :Battery Alarm: Alarme batterie: :Touch Screen: Ecran tactile: :Sticks: Manches: :Turn Off Désactiver :Turn On Activer :Scanner Scanner :No Trims Pas de Trim :4 Outside 4 Extérieurs :4 Inside 4 Intérieurs :6 Trims 6 Trims :No Bars Désactivé :4 Bars 4 Barres :8 Bars 8 Barres :Box %d: Box%d: :Timer1 Timer1 :Timer2 Timer2 :Bar %d: Barre %d: :Toggle%d Boutton%d :Trims: Trim: :Bars: Barres: :Main Page Config Page de config. principale :Timer Timer :Switch: Commande: :Start: Start: :stopwatch Chronomètre :countdown Décompte :Normal Normal :Inverted Inversé :Helicopter Helicoptère :Airplane Avion :SwashType: Plateau cyclique: :COL Src: Source du pas: :ELE Inv: :Sens profondeur :AIL Inv: :Sens aileron :COL Inv: :Sens du pas :Input: Entrée: :Trim -: Trim -: :Trim +: Trim +: :Trim Step: Finesse: :Trim Trim :No Trim Pas de Trim :Src: Source: :Curve: Courbe: :Scale: Echelle: :Offset: Offset: :Min: Min: :Max: Max: :Mid-Rate Déb. Med :Low-Rate Déb. bas :Src Source :Switch1 Inter1 :Switch2 Inter2 :High-Rate Déb. Haut :Linked Lié :Mixers: Mixers: :Page: Page: :Mux: Opération: :replace Remplacer :mult Mult. :add Ajouter :Reverse: Sens: :Failsafe: Failsafe: :Safety: Sécurité: :Value: Valeur: :Subtrim: Subtrim :Reversed Inversé :Point: Point: :Pos/Neg: Pos./Neg.: :Symmetric Symétrique :Pos Pos. :Neg Neg. :Save Sauve :Touch to Unlock Toucher pour déverrouiller :Touch to Lock Toucher pour verrouiller :Channels Voies :Inputs Entrées :Buttons Boutons :Model Modèle :File: Fichier: :Model Name: Nom de modèle: :Model Type: Type de modèle: :Protocol: Protocole: :Number of Channels: Nombre de voies: :Tx Power: Puissance TX: :Fixed ID: ID fixe: :Bind Appairage :Load... Charger... :Copy To... Copier... :Template.. Modèle... :Reset Reset :USB USB :Deviation FW\nversion: Deviation FW\nversion: :USB File System is disabled\nPress 'Ent' to Gestion USB désactivée \nAppuyer sur 'ENT' pour :enable Activer :disable Désactiver :%s is %d%%, safe value = %d%%\n %s = %d%%,valeur sécu. = %d%%\n :Safety Sécurité :\n\nBinding will end in %d seconds... \n\nFin d'appairande dans %d secondes... :Binding is in progress...\nMake sure model is on!\n\nPressing OK will NOT cancel binding procedure\nbut will allow full control of Tx. Appairage en cours...\nAssurez vous que le récepteur fonctionne\n\nAppuyer sur OK n'annulera pas la procédure \nmais permettra le contrôle du TX. :Binding Appairage :Simple Simple :Expo&DR Expo&DR :Complex Complexe :USB Storage mode, press 'ENT' to exit. Mode de stockage USB, appuyer sur 'ENT' pour sortir. :Filesystem could not be mounted. Create the FS via USB, then press 'ENT' to exit. Le système de fichier ne peut être monté.\nAppuyer sur 'ENT' pour sortir. :1-to-1 1 vers 1 :Fixed Fixe :Min/Max Min/Max :Zero/Max 0/Max :> 0 > 0 :< 0 < 0 :ABSVAL ValAbs :EXPO EXP. :3 Point 3 points :5 Point 5 points :7 Point 7 points :9 Point 9 points :11 Point 11 points :13 Point 13 points