Advanced Search

It is Greate, I see My Devo F12E through your picture. Thank you very much.

I recently bought a Devo F12E complete FPV system and was wondering if the Devo 12S software will work on my system. Any help will be appreciated. Thanks.

Garry

You can email me any responses to This email address is being protected from spambots. You need JavaScript enabled to view it..

Tks again.

That is great information -- thanks for it. I've managed to make the physical connection via some kludging -- shown in the attached picture.

Hopefully the rest of the setup goes smoothly!

Hi,
I don't have a Devo F12E, but an 9XR with a pixhawk. I don't use either the ppm encoder as i have a ppm sum output on my rx.
But i can tell you that you have to plug :
The RX1202 AILE chan on channel 1 (as marked on the ppm encoder), ELEV on channel 2, THRO on channel 3, RUDD on channel 4.
Channel 5 is usually used for flight mode, you will have to find a 6 pos inter and send different value. (I use OpenTX mixing and use one 3 inter pos and one 2 inter pos).
Channel 6 can be used for a lot of thing, look in mission planner (for exemple, fine tune the PID value)
Channel 7 and 8 can be used for gimbal (use a potentionmeter).

Regards,
camousse

I am trying to setup my pixhawk px4 to run with my rx1202 that came with my devo f12e. I am trying to determine how to configure channels 1 through 8 between the rx and the tx. All very confusing. It would be nice if the devo f12e had a setup guide for a multirotor wouldnt it?
I have included a photo so you can see what it is I am trying to do. If anybody can help me figure out the best way to plug the wires into the rx, and how to setup the controller.

Thanks so much for any help you can offer!
Mike

Grrrr.... dommage

i receved my F12E whit rx1202 white,failsafe it's ok in this Rx?

F12E FPV screen PCB

F12E FPV other side

Great thing - any chance to take pictures of the other sides of the PCBs of your F12E ?

There must be some kind of display driver hidden, and also knowing the part number of the display (usually printed on the backside) would be great.

I have photos of my F12E FPV

Hi, i by DEVO F12E transmitter, it's ok for the DeviAtion prog?

This is the deviation forum. People here don't use the stock firmware so it might be hard to get help.

Anyway if you want to contribute it would be very nice if you could take pictures of the inside of the F12E so we can see if there's hope to see deviation run on it one day.

hi
I bought a devo F12E for my QR 350 pro, does anyone have the seetings for it.
and how to get the ilook+ to start recording

PhracturedBlue wrote: It looks nice, but I got burned by the F7, so I'm not sure I want to spring for the F12 until we have some idea what is inside it.

Hi PB- just to add another voice to this- I'm thinking of either a devo 12s, or this new f12e- there's only £10 between them in the uk. I take it walkera are moving away from the architecture deviation runs on?

Hi All, I was thinking of buying a Devo F12 FVP TX. But I like my Spektrum DX8 so much.
I have 7 Helli's and 6 multi copters. It would be nice to have them all on one TX with 5.8GHz video receive.

At the moment all my helli's and multicopters are on DSM2 and DSMX with a 5 inch TFT screen sitting on top of my DX8 with a 3S lipo stuck to the back of it.

Most of them use 7Ch but my Octo copters use 8Ch so a F7E is out of the question.
So would the 12S firmware go on to the F12 FVP?

I see that Walkera are bringing out a F12E with the screen on top.
Looks like a very nice TX.

Hi,

also very interesting: Devo F12E
walkera-fans.de/devo-f12e (German)
More informations are difficult to find.

Greetings from Stuttgart
Martin