Walkera Master CP - Standard Settings

More
07 Jan 2014 02:25 - 30 Apr 2014 15:17 #18121 by Tom Z
  • Throttle hold on the RUDD D/R switch.
  • 7 Point Throttle and Pitch Curves.
  • TX Power=100mW
  • Channels=7
  • Protocol=DEVO
  • No Fixed ID
  • Stick Mode 2
  • If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.



    Model 11 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

    * This model will not work for deviation firmware v2.1 or v3.

    Model 11-2 has Zero Degree Pitch when throttle hold is on.
    This will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch.
    This will also help prevent a boom strike.
    The swash does not move when TH is on.
    If you want control of the swash in TH to help you land in a crash don’t use this model use Model 11 instead.



    I have test flown this model in my Devo 10.


Fixed ID

My model does not use a Fixed ID.
If you used a Fixed ID with the original Walkera firmware you must clear the Fixed ID in the Receiver with the Bind Plug.
If you don't clear the Fixed ID the model will not bind.

If you want to use a Fixed ID you can enter the same Fixed ID you had for the original Walkera firmware.

Example: Your original Walkera firmware Fixed ID was: 123456

Assign the Deviation Fixed ID: 123456

You can also assign any Fixed ID that you want to use. You don't have to use the original Walkera firmware Fixed ID. Clear the Fixed ID in the Receiver with the Bind Plug then assign any Fixed ID that you want to use.




Throttle Curve

Normal: Linear Curve

ST-1 : V Shaped Throttle Curve

ST-2: 100% Flat Across


Throttle Hold is active on RUDD D/R switch



Pitch Curve

Normal: -3* negative pitch. Zero degrees pitch at mid stick.

ST-1: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.

ST-2: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.



Gyro Gain

64% for Normal and Stunt modes. This value is equal to the Walkera firmware value of 82% gyro gain.



DR/EXPO

Adjust D/R and EXPO to your personal preference.


Switch Position

0- ELEV D/R = 70% EXP +30%

0- AILE D/R = 70% EXP +30%

RUDD D/R = 100% EXP LIN



Switch Position

1- ELEV D/R = 100% EXP +30%

1- AILE D/R = 100% EXP +30%

RUDD D/R = 100% EXP LIN






Download the Configuration Settings File.

Right click the "model.ini " and select "Save Target As" or "Save Link As" depending if you are using IE or Firefox.

Install the configuration settings file into your models folder (See my How to video below).

This will over-right the current file so make sure that model slot doesn’t
have a model being used in it. If it does rename the configuration settings file
to another number that you have free.

Example: The file you downloaded is named model5 so change the “5" to another slot
number that you don’t have a model setup for. If you have model slot 6 open rename the file to model6





How to Import/Export Deviation Firmware Models




Attachments:
Last edit: 30 Apr 2014 15:17 by Tom Z.

Please Log in or Create an account to join the conversation.

More
18 Oct 2015 16:56 #39023 by Stavridis
Replied by Stavridis on topic Walkera Master CP - Standard Settings
Hi Tom!
What is the difference between 1st and 2nd .ini file?

Please Log in or Create an account to join the conversation.

More
23 Oct 2016 16:23 #55311 by MarioCaxito
Replied by MarioCaxito on topic Walkera Master CP - Standard Settings
Hello friend, I'm picking up with the deviation. I can not set anything. I tried to follow the step without success. Could you please make a video programming the radio to the PC MASTER. Thank you.

Please Log in or Create an account to join the conversation.

Time to create page: 0.033 seconds
Powered by Kunena Forum