EAchine E012

EAchine E012 was created by goebish

Hi there !

SeByDocKy has found that the new EAchine E012 Tx is using an HS6200 transceiver, I might be able to emulate it with the nrf24l01, only if the protocol is not using 500kbps bitrate.

Can someone make a dump of the SPI bus in the stock Tx so I can check that ?

Here's the pinout:

I need CE, CSN, SCK, MISO, MOSI and IRQ (GND = VSS)

If it's using 1Mbps or 2Mbps bitrate I should be able to add it to Deviation once I get one (I'll need one because captures over the air are necessary to reverse the scrambling).

Please Log in or Create an account to join the conversation.

Replied by SeByDocKy on topic EAchine E012

Ok I will try to solder ..... I can't promise .... yet ...

Please Log in or Create an account to join the conversation.

Replied by goebish on topic EAchine E012

As I said, don't ruin your Tx if you're not confident enough with the soldering job, nobody is in a hurry, right ?

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Replied by SeByDocKy on topic EAchine E012

Ok I start to have signal but the decoding is not correct ....

Anyone can recognize which one is the clock, mosi, miso and enable ?

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Replied by SeByDocKy on topic EAchine E012

goebish wrote: Seems clock & enable are wrong, maybe their wires are shorted with other pins somehow ?
Also, enable in Logic should be connected to CSN (Chip Select when Negative), not CE.

I checked I have no short on any wires ....

Now I am on CSN but not better

Are CSN & SCK inverted ?

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Replied by SeByDocKy on topic EAchine E012

I sollved the short with SCK with the adjacent pin of the MCU ... but still not working ;(

Please Log in or Create an account to join the conversation.

Replied by goebish on topic EAchine E012

Well, don't spend too much time on that (and don't kill your Tx!) directly connect ground to battery - and try to keep the wires as short as possible as it seems it's using a rather high clock rate.... and the kind of wires you're using, wrapping wire, is far from being ideal for this job (you should get some stranded 30awg silicone wires such as www.ebay.com/itm/1M-3-3ft-30AWG-Flexible...6color-/252562300800 ).
I'll just order one

Please Log in or Create an account to join the conversation.

Replied by SeByDocKy on topic EAchine E012

goebish wrote: Well, don't spend too much time on that (and don't kill your Tx!) directly connect ground to battery - and try to keep the wires as short as possible as it seems it's using a rather high clock rate.
I'll just order one

Maybe my wires are too long ... coz I had to make a kind of double extension to solder these flucking duponts wires.... ....

Please Log in or Create an account to join the conversation.

Replied by SeByDocKy on topic EAchine E012

Solved the GND was guilty

Please Log in or Create an account to join the conversation.

Replied by goebish on topic EAchine E012

Yeah, wrapping wire sucks for this kind of job
It's meant to be wrapped around some pins with a special tool, not soldered:

Please Log in or Create an account to join the conversation.

Replied by SeByDocKy on topic EAchine E012

Ok first captures

mon-partage.fr/f/yRXyiYvF/

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.

Please Log in or Create an account to join the conversation.