Dfuse - Unable to find devention device... Bad fir

Start
Prev
1
Next
End

sbstnp
Topic Author
Offline

07 Aug 2013 07:44 #12804 by sbstnp

Dfuse - Unable to find devention device... Bad fir was created by sbstnp

Can you upload a screenshot?

Devo 10 + 4in1
~~Spektrum Dx9~~
FrSky Taranis + TBS Crossfire

Please Log in or Create an account to join the conversation.

FDR
Offline

07 Aug 2013 08:59 #12806 by FDR

Replied by FDR on topic Dfuse - Unable to find devention device... Bad fir

The v1.41 doesn't support the DEVO 7E, it appeared first in the v1.5

Please Log in or Create an account to join the conversation.

rbe2012
Offline
So much to do, so little time...

07 Aug 2013 14:55 #12814 by rbe2012

Replied by rbe2012 on topic Dfuse - Unable to find devention device... Bad fir

The diode must be shortened - does not matter if it stays on the board or not. So you could use something what is called "Leitlack" in German - a liquid color containing metal parts which will make an electrical connection when dried. You just have to draw a line between both ends of the diode.

Please Log in or Create an account to join the conversation.

PhracturedBlue
Offline

08 Aug 2013 02:02 #12827 by PhracturedBlue

Replied by PhracturedBlue on topic Dfuse - Unable to find devention device... Bad fir

I use 'rear-window defroster' fixer. You get a tiny little bottle from the automotive store for like $13US, but it does the job.

Please Log in or Create an account to join the conversation.

rbe2012
Offline
So much to do, so little time...

08 Aug 2013 09:10 #12836 by rbe2012

Replied by rbe2012 on topic Dfuse - Unable to find devention device... Bad fir

Looks as if it should work, but I have no experiences with this.

Please Log in or Create an account to join the conversation.

FDR
Offline

08 Aug 2013 13:02 #12844 by FDR

Replied by FDR on topic Dfuse - Unable to find devention device... Bad fir

No the fw can't know about the diode mod, you have to tell him by editing the tx.ini file.
Without a power amp the RF chip is have to be configured to use the max power, which would be the 150mW option if there was a power amp...

Please Log in or Create an account to join the conversation.

PhracturedBlue
Offline

08 Aug 2013 14:54 #12846 by PhracturedBlue

Replied by PhracturedBlue on topic Dfuse - Unable to find devention device... Bad fir

ixlix wrote: would "Silver Conductive Wire Glue" from ebay be similar?

The stuff in a syringe is probably fine, but ships from China (which may or may not be an issue depending on where you are)
The stuff in a jar is basically graphite powder in a binder, and tends to shrink when it dries (though for this application it probably won't matter)

Please Log in or Create an account to join the conversation.

jason4207
Offline

09 Aug 2013 04:56 #12857 by jason4207

Replied by jason4207 on topic Dfuse - Unable to find devention device... Bad fir

ixlix wrote: So after playing around with the tx i noticed that on the screen it says under the battery voltage "150 mW", now is that standard on the 7e or have i managed somehow to actually do the mod? I havent adjusted the tx.ini as i didnt think it worked and i aborted my attempt. I did get a tiny ball of solder on an adjacent diode but i checked and it didnt look like t bridged to the other end. Hmmm.

Are you using the stock radio module or an added module when you see this? What are you flying?

What does your tx.ini file show?

Please Log in or Create an account to join the conversation.

Start
Prev
1
Next
End

Time to create page: 0.115 seconds

Re-enable mobile display