Advanced Search

At "About" page you have to see "ir8m-v5.x.x-2018-01-25".

Try to slow format USB drive and write filesystem from archive. Use "Safely Remove Hardware" after writing filesystem.

Transmitter powering up problem

If I turn off the transmitter I can’t turn it back on.

I tried unplugging the AA battery module and it often times still doesn’t power up.

At first I thought I had a bad batch of batteries but it still does it even with a fresh batch.

Sometimes waiting for more than few minutes does power it back up.

Does anyone else have this issue and possible fix?

Unable to Bind to a Bwhoop Pro using the Bayang Protocol.

I go to initialize with it and it just doesn't bind.

Tips anyone?

I attempted to update my iRange Transmitter using the latest build but the start screen does not show the latest build number which I assume means it did not update.

Also, The Transmitter freezes up when I try to change the icon.

Have I done something wrong?

To run the remote control with the new receiver you need a specific software for the receiver. Not every version works. It is very important to set the value to 40-41 as in the photo.

Since iRangeX iRX-IR8M has different LCD, RUD and AIL reversed vs Jumper T8SG and it can use 4xAA battery, we need different build for iRX-IR8M. At least for some time.

You can find fresh iRangeX iRX-IR8M builds at Builds category:
www.deviationtx.com/forum/builds/7605-irangex-irx-ir8m-builds

Since iRangeX iRX-IR8M (t8sg-v5.x.x-2017-09-19) is somewhat different from Jumper T8SG I will place here the builds for iRangeX iRX-IR8M.

Changes:
* RUD and AIL reversed to comply with common direction for Deviation.
* AUX4 and AUX5 reversed to comply with common direction for Deviation.
* All switches reversed to comply with common direction for Deviation.
* batt_critical set to 3900 since iRX-IR8M can use 4xAA battery.
* LCD Internal Resistor Rate (Rb/Ra) set to 4 (0x24).

(2018-01-26)
iRangeX iRX-IR8M based on Nightly Builds:

File deleted, see below...

Thank you, I have all necessary information.

vlad_vy wrote: OK. Can you try next build with wider contrast range and report last contrast value before screen become black.

Attachment not found

It's completly black at 9 .... This one with the default 5 value offers more black than first tested release. I needed to set to 3 to retrieve same contrast as before

OK. Can you try next build with wider contrast range and report last contrast value before screen become black.

File deleted...

The built x24 is working flawless Thanks

Try these two builds with different contrast setting (last number at archive name = 24 or 25) and say which will be better. I think it will be 24. Also, try with all contrast settings (off, 1-10).

Files deleted...

I just flashed the last Jumper T8SG NB and the radio boots ok but the backlight colored are inverted ......




So I guess the correct NB to flash is more the U7E ....

Centering issue could still be mechanical, this is worth a read.
www.deviationtx.com/forum/6-general-disc...tick-centering-issue

Hello Folks.

Has anyone been experiencing the same issues with the awkward centering of the gimbals?

If you have experienced this, do any of you have a solution or an idea for a solution?

I havn't iRangeX iRX-IR8M but from images it looks like it is Flysky AFHDS 2A receiver:
www.banggood.com/818CH-Mini-Receiver-Wit...rch&cur_warehouse=CN

If it doesn't bind, try to use "Freq Tune" protocol option with step 10-20.

Has anyone already managed to tie the remote control to the receiver that is there? I can not do it !!!!!

Can nobody help me?

I think outer 2-pos switches can be replaced by 3-pos switches without any mods. The shoulder 2-pos switches can be modded to "H" and "G" switches the same way as for T8SG.

I found that the two shoulder 2-way and the two pots are connected togather !!!!! as AUX4 & AUX5.... It's a bit crazy.... but in practice if you calibrate with the pot, it's well proportional to the input....

Here the default built installed in case it's not the strict indentical with the T8SG build but I think it's the same build.....